As I said, it is still a manual process where tools can aid.
FTester has a large manual component. The file - "ftest.conf" has to be
created separately (manually) for every system, range of policies etc.
Regards,
Craig Wright
GSE-Compliance
Craig Wright
Manager of Information Systems
Direct : +61 2 9286 5497
Craig.Wright@bdo.com.au
+61 417 683 914
BDO Kendalls (NSW)
Level 19, 2 Market Street Sydney NSW 2000
GPO BOX 2551 Sydney NSW 2001
Fax +61 2 9993 9497
www.bdo.com.au
Liability limited by a scheme approved under Professional Standards Legislation
in respect of matters arising within those States and Territories of Australia
where such legislation exists.
The information in this email and any attachments is confidential. If you are
not the named addressee you must not read, print, copy, distribute, or use in
any way this transmission or any information it contains. If you have received
this message in error, please notify the sender by return email, destroy all
copies and delete it from your system.
Any views expressed in this message are those of the individual sender and not
necessarily endorsed by BDO Kendalls. You may not rely on this message as
advice unless subsequently confirmed by fax or letter signed by a Partner or
Director of BDO Kendalls. It is your responsibility to scan this communication
and any files attached for computer viruses and other defects. BDO Kendalls
does not accept liability for any loss or damage however caused which may
result from this communication or any files attached. A full version of the
BDO Kendalls disclaimer, and our Privacy statement, can be found on the BDO
Kendalls website at http://www.bdo.com.au or by emailing
administrator@bdo.com.au.
BDO Kendalls is a national association of separate partnerships and entities.
-----Original Message-----
From: listbounce@securityfocus.com [mailto:listbounce@securityfocus.com]
On Behalf Of Captain Bock
Sent: Thursday, 25 October 2007 1:19 AM
To: security-basics@securityfocus.com
Subject: Fwd: Firewall rulebase audit
I used FTester in a recent test campaign with very interesting results.
U can find this at:
http://dev.inversepath.com/trac/ftester
All the best
Captain Bock
On 10/24/07, Craig Wright <Craig.Wright@bdo.com.au> wrote:
These are a manual process. Tools may aid in the process, but it is
still a process of comparing config to policy (and hopefully one
exists).
No tool can decide what is good for a firm/company. Tools will help
extract the data, but to my knowledge there is no expert system that
will analyse a company security policy and map it to a list of ingress
and egress filters. (Maybe a good topic for a hopeful PhD candidate in
Computational Linguistics, Computational learning and Security).
Regards,
Craig S Wright
GSE-Compliance
Craig Wright
Manager of Information Systems
Direct : +61 2 9286 5497
Craig.Wright@bdo.com.au
+61 417 683 914
BDO Kendalls (NSW)
Level 19, 2 Market Street Sydney NSW 2000
GPO BOX 2551 Sydney NSW 2001
Fax +61 2 9993 9497
www.bdo.com.au
Liability limited by a scheme approved under Professional Standards
Legislation in respect of matters arising within those States and
Territories of Australia where such legislation exists.
The information in this email and any attachments is confidential. If
you are not the named addressee you must not read, print, copy,
distribute, or use in any way this transmission or any information it
contains. If you have received this message in error, please notify the
sender by return email, destroy all copies and delete it from your
system.
Any views expressed in this message are those of the individual sender
and not necessarily endorsed by BDO Kendalls. You may not rely on this
message as advice unless subsequently confirmed by fax or letter signed
by a Partner or Director of BDO Kendalls. It is your responsibility to
scan this communication and any files attached for computer viruses and
other defects. BDO Kendalls does not accept liability for any loss or
damage however caused which may result from this communication or any
files attached. A full version of the BDO Kendalls disclaimer, and our
Privacy statement, can be found on the BDO Kendalls website at
http://www.bdo.com.au or by emailing administrator@bdo.com.au.
BDO Kendalls is a national association of separate partnerships and
entities.
-----Original Message-----
From: listbounce@securityfocus.com
[mailto:listbounce@securityfocus.com]
On Behalf Of Kevin Ortloff
Sent: Wednesday, 24 October 2007 2:09 AM
To: Roman; jctx09@yahoo.com
Cc: security-basics@securityfocus.com
Subject: RE: Firewall rulebase audit
I would say that the best audit for firewalls are manual. There are
tools that can point things out to you, but usually I run nessus or
similar from the outside to gain knowledge of open ports, then I
manually go through the acl's. Once, that's cleaned up, look at your
object groups, hit counters, and translations.
-----Original Message-----
From: listbounce@securityfocus.com
[mailto:listbounce@securityfocus.com]
On Behalf Of Roman Shirokov
Sent: Thursday, September 20, 2007 5:09 AM
To: jctx09@yahoo.com
Cc: security-basics@securityfocus.com
Subject: Re: Firewall rulebase audit
Hi
You can check check this:
CIS Level 1 & 2 Benchmarks and Audit Tool for Cisco IOS Routers and
PIX
firewalls.
http://cisecurity.org/bench_cisco.html
I have a pair of PIX firewalls that I need to audit. I was hoping to
get some guidelines for doing this. Antyhing specific to PIX would
be
even better.
1) What is the best/easiest way to document a current policy?
Spreadsheet?? I would like to know what ports (services) are open
and
to where? Also duplicates, etc.? Would it be best just to put it in
a
spreadsheet? Is there a tool for this?
2)Is there standard Analysis checklist to go by when reviewing a
(PIX)
firewall policy?
Any help is highly appreciated.
Thank you,
__________ NOD32 2541 (20070920) Information __________
This message was checked by NOD32 antivirus system.
http://www.eset.com
--
Best regards,
Roman Shirokov
e-mail:insecure@yandex.ru
Life has more imagination than we carry in our dreams... (Christopher
Columbus)
This email, its contents and attachments contain information from j2
Global Communications, Inc. and/or its affiliates which may be
privileged, confidential or otherwise protected from disclosure. The
information is intended to be for the addressee(s) only. If you are
not
an addressee, any disclosure, copy, distribution, or use of the
contents
of this message is prohibited. If you have received this email in
error
please notify the sender by reply instant message mail and delete the
original message and any copies.
