Ethical Hacking Learn to find vulnerabilities before the bad guys do! Gain real world hands on hacking experience in our state of the art hacking lab. Course designed and taught by expert instructors with years of penetration testing experience. 12 student maximum in every class. Certification attempt included in every package. | Computer Forensics Training at InfoSec Institute Gain the in-demand skills of a certified computer examiner, learn to recover trace data left behind by fraud, theft, and cybercrime perpetrators. Discover the source of computer crime and abuse at your organization so that it never happens again. All of our class sizes are guaranteed to be 12 students or less to facilitate one-on-one interaction with one of our expert instructors. |

| Subject: | PIX 6.2(2) behaviour for traffic from lower to higher level |
|---|---|
| Date: | Mon, 28 Aug 2006 23:48:18 +0530 |
Hi all,
I am working on a lab PIX loaded with 6.2(2)
Here is the BASE configuration: -------------------------------------------------------- nameif ethernet0 outside security0 nameif ethernet1 inside security100 nameif ethernet2 DMZ security50
ip address outside 200.200.200.2 255.255.255.0 ip address inside 21.21.21.2 255.255.255.0 ip address DMZ 22.22.22.2 255.255.255.0
Host A on DMZ: 22.22.22.3 (g/w: DMZ IP) Host B on inside: 21.21.21.3 (g/w: inside IP)
ACL applied:
access-list acl-dmz permit icmp any any echo access-list acl-dmz permit icmp any any echo-reply
access-group acl-dmz in interface DMZ --------------------------------------------------------
############## *Condition1: (No nat0 or static command and XLATE table is empty)* If I initiate a ping from A to B (lower to higher), I get the translation error:
*305005: No translation group found for icmp src DMZ:22.22.22.3 dst inside: 21.21.21.3 (type 8, code 0)*
*Condition2: (nat0 for DMZ subnet)*
I add the below to BASE config: nat (inside) 0 21.21.21.0 255.255.255.0
I still get the 305005 error.
*Condition3: (no nat0 or static command)*
I add these to BASE configs:
PIX-515(config)# nat (DMZ) 1 22.22.22.3 255.255.255.255
PIX-515(config)# global (inside) 1 22.22.22.3 255.255.255.255 (dmz to inside translation)
Still, I get the 305005 error.
*Condition3: (no nat0, but static command for dmz host B)*
I add the following command static (dmz,inside) 22.22.22.3 22.22.22.3 netmask 255.255.255.255 (static NATing A)
Still, the error remains. ##############
I am able to ping B from A only under below conditions:
1. nat (inside) 0 21.21.21.0 (B's subnet) *........OR...* ** 2. static (inside,dmz) 21.21.21.3 21.21.21.3 netmask 255.255.255.255 (static NATing B) #############
AFAIK, an ACL on the DMZ (lower security) to allow ICMP should allow the ping. I just confirmed it on a 525 box running 7.0.
What is going wrong in the three conditions above? Is my understanding incorrect?
-- Warm regards,
Amol Sapkal
------------------------------------------------------------------- "When I'm not in my right mind, my left mind gets pretty crowded" -------------------------------------------------------------------
| <Prev in Thread] | Current Thread | [Next in Thread> |
|---|---|---|
| ||
| Previous by Date: | AW: Stale IKE SA on FW-1, Meidinger Chris |
|---|---|
| Next by Date: | Can phase 2 proxy-id be modified on SonicWall VPN's?, Neal Stroh |
| Previous by Thread: | AW: Stale IKE SA on FW-1, Meidinger Chris |
| Next by Thread: | Can phase 2 proxy-id be modified on SonicWall VPN's?, Neal Stroh |
| Indexes: | [Date] [Thread] [Top] [All Lists] |